(Click on items for their description)
Closed Side Guide

Is used for shifting sawn wood blocks as far as maximum working width of machine - by the type of machine:

ORBIT - maximum working width "B" = 150 mm

ECO-POWER - maximum working width "B" = 150 mm

MAMUTH - maximum working width "B" = 220 mm

This equipment is possible use for working up of almost kinds of sawn wood blocks. We recomme to worked up two side planned sawn wood - lower surface and side surface. Height tolerance 0.1 mm must be observed. Sawn wood blocks are pressed against Side-press equipment by the pneumatic cylinder. This equipment is not suitable for working up of sawn wood blocks, which have thickness below 30 mm.

Frame Saw Side Guide
 
Side Guide

 

Closed Central Guide

Central Guide is used for processing of two wooden blocks at the same time. For properly function must be clarified a height tolerance of wooden blocks 0.1 mm. Blocks are pressed against the Central-Guide-Equipment by means of pressure levers adjusted by the four pneumatic cylinders or by the four setting screws. Maximum working width of blocks are limited:

ORBIT - maximum working width "B" = 65 mm

ECO-POWER - maximum working width "B" = 65 mm

MAMUTH - maximum working width "B" = 100 mm

This equipment is not suitable for processing of wooden blocks, which thickness is less than 30 mm.

Frame Saw Center Guide
 
Central Guide

 

Closed Channel Guide

Channel Guide is used for processing of several wooden blocks at the same time. For properly function must be clarified height tolerance of wooden blocks 0.1 mm. Blocks are guided towards the saw blades between the steel bars. For properly function of this system must be clarified surfaces and edges processing. We recommend four-side-preplaned sawn wood with accuracy of 0.1 mm. Max. number of the channels depends on the working width of machine and on the thickness of the sawn wood.

Frame Saw Channel Guide
 
Channel Guide

 

Closed Stretching Frame

Stretching Frame is used for tensioning of the saw blades. Mounting of the Stretching Frame are made by means of the Mounting Frame. Stretching Frame with saw blades is fastened in the Main Carriage Frame of machine in simply way. It is possible to add to every machines arbitrary of Stretching Frames. Type of Stretching Frame depends on type of the machine and on length of saw blades. (according to height of cutting kerf)

Frame Saw Stretching Frame
 
Stretching Frame

 

Closed Saw Spacers with holes

Saw Spacers eliminate a gap between saw blades and so they indicate thickness of the lamellas(slats). Saw Spacers with holes are determined for the Bottom Holder of saw frame. Material of spacers is heat-treated.

Frame Saw Spacer with Hole
 
Saw Spacer with hole

 

Closed Saw Spacers without holes

Saw Spacers eliminate a gap between saw blades and so they indicate thickness of the lamellas(slats). Saw Spacers with holes are determined for the Top Holder of saw frame. Material of spacers is heat-treated.

Frame Saw Spacer
 
Saw Spacer without hole

 

Closed Bottom Outfeed Planing Module

Bottom Planing Module on outfeed removes minor splinters on the bottom side of lamellas(slats). Draft of bottom module is fluently adjusted in and extent 0-2 mm. Resultant measurement of planned lamellas is in accurate measure 0.1 mm. Machine is developed with Electronic measuring on customer demand. First of all it is determined for exact production of parquetry.

Frame Saw Bottom Planer
 
Bottom Planing Module

 

Closed Top and Bottom Outfeed Planing Module

Top and Bottom Planing Module on outfeed serves for removing torn out wood fibres from bottom and top side of material being cut. It serves at the same for accurate high-gauging of produced lamellas(slats). The Bottom Planing Module is component of the Top Planing Module. The draft of bottom module is fluently adjusted in extent 0-2 mm. Bottom module is possible adjust to the whole working range of machine. Resultant measurement of processed lamellas is in an accurate measurement 0.05 mm. It is possible to equip module with electronic measuring with possibility of subtraction of both values of planing modules and its absolute value = resulted measurement of product. First of all it is determined for exact production of parquetry.

Frame Saw Top & Bottom Planer
 
Top and Bottom Planing Module

 

Closed Top Infeed Planing Module

Top Infeed Planing Module installed on the Thin Cutting Frame Saw infeed helps calibrate your input material in order to ensure proper feeding through the machine. You don't need to calibrate the material in height and process it directly after the multi-rip saw process.

Frame Saw Top Infeed Planer
 
Top Infeed Planing Module

 

Closed Rubber Coating of the Top(Bottom) Rollers

The layer of PU on feed rollers ensures feed of wooden blocks - eliminates different of block heights. This method is used in combination with Central-Guide-Equipment or Channel-Guide.

Frame Saw Rubber Roller
 
Rubber Coating of the Roller

 

Closed Automatic Hopper Feeder

Automatic Hopper Feeder is fixed for automatic putting of sawn wood blocks in machine - pneumatic cylinder pushes the wooden blocks into machine. The use is especially suitable in combination with Channel-Guide or for processing of the short wooden blocks. By using of the Automatic Hopper Feeder more machines can be operated by one worker. There is no limit for length of wooden blocks form 200 mm to 4000 mm...and more

Frame Saw Hopper Feeder
 
Automatic Hopper Feeder

 

Closed Adjustable Chip Breaker between blades

Chip Breaker prevents making of split on the bottom side of wooden blocks. Chip Breaker supports processed wood near of the saw blades. The using is especially suitable for production of thin-lamellas or for cutting of wood with different structure of the spring and summer wood.

Frame Saw Chip Breaker
 
Adjustable Chip Breaker between blades

 

Closed Air Blast System (Top and Bottom)

Air Blast System is determined for higher cutting-heights (above 100 mm). Saw blades are cooled with compressed air expansion. Top-Air Blast System helps to blow out the sawn-dust and splinters out of kerfs. You can prolong the live time of saw blades up to 30% with using of this equipment

Frame Saw Air Blast System
 
Air Blast System (Top and Bottom)